CONTACTS
SUBJECTS
Armoire Conversion Modify Cabinetry HD Television 42" x 27" Procurem
1203 -
1203 - ..
1204 - Summary/Objective
1205 -
120501 - Follow up ref SDS 8 0001, ref SDS 7 0000.
120502 -
120503 - Good meeting with Paul today clarifying scope of work, ref SDS 0 JM8T,
120504 - and getting dimensions. ref SDS 0 JX6F Paul will make preparations
120505 - and schedule to complete work on site 120120. Payment upon
120506 - completion. ref SDS 0 FL5N
120507 -
120508 -
120509 -
120511 - ..
1206 -
1207 -
1208 - Progress
1209 -
120901 - Kephart Cabinerty Proposal Armoire Conversion
120902 -
120903 - Follow up ref SDS 8 IR5H, ref SDS 7 IR5H.
120904 -
120905 - 925 827 1093
120907 - ..
120908 - Reviewed planning and agreed to scope listed on 111208 2057.
120909 - ref SDS 6 JB9H
120911 - ..
120912 - Discussed additional issues....
120913 -
120914 - 1. Objective - maintain existing standard of highest quality
120915 - furniture.
120917 - ..
120918 - 2. Remove existing television stand structure.
120919 -
120920 - Bottom panel of existing television controller compartment may
120921 - be difficult to remove. Additionally, removal could cause
120922 - damage to the surface of existing shelf, which can be
120923 - problematic to finish. During performance of the work, if the
120924 - bottom panel proves difficult to remove, then will leave it in
120925 - place and remove the vertical sides and the cross shelf where
120926 - the current television is sitting.
120928 - ..
120929 - 3. Hanger pole - removing pole bracket on the left end exterior
120930 - panel may create a small area that is difficult to finish.
120931 - Decided that since this will be covered by the television it
120932 - can be finished as well as possible, even painted black.
120934 - ..
120935 - 4. Existing drawer - one small drawer will be removed and not
120936 - replaced to make room for the larger size television. During
120937 - the meeting today, there was difficulty in the time available
120938 - to inspect and determine how to remove the drawer. There is
120939 - some type of safety catch that must be released, and this will
120940 - be done by Paul at the time the new shelf is installed.
120942 - ..
120943 - 5. Mid-vertical panel might be plywood, and so vertical cut
120944 - requires adding a piece of solid wood and additional stain
120945 - finish to make a good appearance, reported in call on 111212
120946 - 0958. ref SDS 7 KP9H If the panel is actually solid mahogany
120947 - like the rest of the armorie, then edge cut can be stained,
120948 - like the shelf, or alternatively painted black as Paul
120949 - discussed during the visit on 111123 1100, ref SDS 3 OO8J
120951 - ..
120952 - 6. Back panel is .25 plywood; and, there is an approximate 6" high
120953 - member across the left side of the armoire to the mid-vertical
120954 - panel that is .75" thick. reported on 111212 0958 at 1838
120955 - ref SDS 7 U25M
120957 - ..
120958 - Paul discussed not extending the shelf to the back panel, but
120959 - instead leave 1.5 inch clearance to pass wiring between
120960 - compartments in order to facilitate hook ups.
120962 - ..
120963 - Decided to extend the new shelf to the back panel and fasten it
120964 - with screws. Paul will cut a 1.5" slot and 10" long on the
120965 - wider side of the vertical panel to provide clearance for
120966 - wiring.
120968 - ..
120969 - Shelf will further require a slot approximately 8 5/8" by 1"
120970 - wide to pass by the remaining mid-vertical panel so that the
120971 - new shelf can be connected with screws to the back panel.
120972 - Consider brackets to support the shelf on either side of the
120973 - slot. Use brackets for existing shelves to be removed.
120975 - ..
120976 - Right end of shelf requires .25" x 3" cut out where the shelf
120977 - meets the back panel, and in order to accomodate insetting the
120978 - shelf .25" by routing the right side panel.
120980 - ..
120981 - Accordingly, fastening the new shelf to the back panel requires
120982 - cutting the back edge to fit different thicknesses of back
120983 - panel, thus...
120985 - ..
120986 - Paul took dimensions on a story pole showing...
120987 -
120988 -
120989 - +--+--------------------------------------------------+--+
120990 - | | +--------------------| |
120991 - | |------------------+----------| | ^ | |
120992 - | | 1.5" +----------+ | | 3 | |
120993 - | | / 10" | | 8 5/8 | |- |
120994 - | | / | | | || |
120995 - | |<--------- 27.25"/---------->| | | || |
120996 - | | / |_| ___ | || |
120997 - | | wiring slot / ^ | || |
120998 - | | / | 20 5/8 || |
120999 - | | 1" slot | | || |
121000 - | | | | || |
121001 - | | 12 " | || |
121002 - | | | | || |
121003 - | | | | || |
121004 - | | | | || |
121005 - | | v v || |
121006 - +--+--------------------------------------------------+--+
121007 -
121008 - |<--------------------- 46 .75"------------------->|
121009 - |<--------------------- 47" shelf---------------->|
121010 -
121011 -
121013 - ..
121014 - 7. Painting shelf will be done by customer.
121015 -
121016 - New shelf will be sanded, and ready for stain/painting?
121018 - ..
121019 - Discussed option of installing the shelf loose, so it can be
121020 - removed and painted for example in the garage, then set in
121021 - place and fastened by the customer.
121023 - ..
121024 - Decided that Paul will securely fasten the shelf into the
121025 - armoire. Customer will paint the shelf in place.
121027 - ..
121028 - Paul has already purchased the material for the new shelf.
121030 - ..
121031 - Offered to pay in full today for the work.
121033 - ..
121034 - Paul said payment can be submitted after the work is completed.
121036 - ..
121037 - Paul scheduled the work on 120120, and complete same day.
121038 -
121039 -
121040 -
121041 -
121042 -
121043 -
121044 -
121045 -
1211 -